1/16 inch to mm: 1.5875 mm

Equivalent forms

• 1/16 inch = 0.0625 inch
• 0.0625 inch × 25.4 = 1.5875 mm
• 1.59 mm rounded to 2 decimals; 1.587 mm rounded to 3 decimals

Where this value appears in manufacturing work

• 1/16 inch commonly shows up in thin shim clearance, laser-cut relief slots, small radius notes, and gauge-strip checks; the converted 1.5875 mm value is the unit reference, not the whole production instruction.
• A fixture technician may see 1/16 inch as a relief notch on a bracket print, while purchasing may read it as shim or strip thickness; both need the same converted reference but different approval evidence. A strong shop note writes 1/16 inch (0.0625 in) = 1.5875 mm reference before adding feature type, tolerance, material, or inspection details.
• Use the conversion to prevent arithmetic and transcription errors, but do not use it to decide assuming the fraction identifies a fastener, drill, thread, wrench, replacement part, or metric standard size.
• For this page-specific manufacturing hook, treat the work artifact as a shim pack traveler or small-feature inspection sheet; record the drawing revision, source units, and process stage beside the metric value.
• small fraction with high measurement-method sensitivity This is why 1/16 inch should keep its original inch notation even when downstream paperwork is metric.
• If a supplier proposes a nearby metric item or a rounded substitute, treat that proposal as a separate review step rather than as a conclusion from 1.5875 mm alone.

When to keep exact decimals vs rounded values

Because 1.5875 mm often becomes 1.59 mm in quick notes, keep the four-decimal conversion when a narrow relief, shim stack, or clearance discussion needs traceability. Keep 1.5875 mm when the converted value is copied into a calculation sheet, QA record, CNC setup note, or RFQ where traceability matters. A shorter display such as 1.59 mm may be readable, but it can hide the source notation and the rounding step. For 1/16 inch, the safer documentation pattern is: 1/16 inch (0.0625 in) = 1.5875 mm reference; see the drawing or process plan for tolerance and usage. This keeps the exact conversion separate from engineering decisions, supplier proposals, and shop-floor adjustments.

Measurement and inspection notes

• For a 1/16 inch feature, pin access, edge burrs, and caliper jaw geometry can dominate the measurement, so the inspection note should say whether the value is checked as a gap, radius, slot, or material thickness.
• For 1/16 inch, first identify whether the feature is a thickness, outside dimension, inside dimension, hole, slot, center distance, spacing, or reference note.
• The exact conversion to 1.5875 mm does not define pass/fail criteria; those come from the drawing, tolerance block, inspection plan, or approved supplier document.
• A caliper, micrometer, gauge pin, indicator, CMM routine, or fixture check can produce different confidence levels for the same converted number.
• Record the original inch value beside the metric value when inspection data must be traceable across inch-based and metric documents.
• Do not infer calibration intervals, certified accuracy, or process capability from this conversion page.

CNC and shop-floor setup notes

• When programming a 1/16 inch relief in metric mode, verify whether the CAM path uses tool-center geometry, cutter radius compensation, or a nominal slot width before copying 1.5875 mm.
• Before entering 1.5875 mm into a CNC setup sheet, confirm whether the program, controller, CAM post, drawing, and operator notes are using inch or metric units.
• If the job is metric on the machine but inch-based in the drawing, show both 1/16 inch and 1.5875 mm so the operator can trace the value back to the source.
• Keep cutter compensation, kerf, stock-to-leave, coating, grinding allowance, finishing allowance, and probing offsets as separate labeled fields.
• Do not silently add or subtract process allowance from the converted value; any adjustment should be visible in the traveler, setup note, or NC documentation.
• Check G20/G21 mode, CAM/post-processor units, and setup-sheet rounding before cutting, probing, or releasing inspection paperwork.

Supplier, drawing, and RFQ communication notes

• RFQs should label 1/16 in as a small-feature reference, not as a generic shim order, unless the material grade, thickness tolerance, and supplier standard are also named.
• A clear supplier line can read: 1/16 inch (1.5875 mm reference), use the drawing revision and stated tolerance for acceptance.
• Include material callout, finish requirement, drawing revision, inspection requirement, and whether the metric number is reference-only or a required converted working dimension.
• Do not send only the rounded millimeter value when the design authority is inch-based, because the supplier may lose the source notation and rounding context.
• If the supplier suggests a nearby stock size, standard item, or substitute, require separate engineering, purchasing, or drawing-owner review.
• Use the conversion as communication support, not as a replacement approval, material equivalence statement, compliance claim, or supplier certification.

FAQs